Sewer Repair – How to Get Rid of Damaged Sewer Lines

Sewer lines can get damaged for a number of reasons. If you notice puddles around your home, squelching noises coming from drains, or foul odors, these could all be signs that your sewer line is in need of repair.

Sewer Repair

Traditionally, these repairs would involve digging up and replacing the entire line. But trenchless methods can now do the job without destroying your property. Visit Website for more information.

Pipe lining is one of the most popular new sewer repair methods available. It can fix backed up, cracked, or broken pipes without the need for digging. It’s also a fast and cost-effective solution. It can be used to line a single section of a damaged pipe, or the entire length of the affected run.

The process of lining a sewer pipe is called cured-in-place-pipe (CIPP). It’s a trenchless method that saves your yard, sidewalk, and brick driveway from being dug up. A felt tube saturated with epoxy is inserted into your existing pipe. A rubber bladder inside the felt tube is inflated, and the epoxy cures to form a strong, durable liner that takes the shape of your old pipe. It’s a quick and inexpensive way to fix problems with older pipes made of clay, cast iron, or concrete.

CIPP is ideal for repairing small to medium-sized runs of damaged pipes, as well as long-distance repairs in hard-to-reach areas. It’s even effective on cast-iron pipes that are in poor condition and may have cracks or leaks. It’s a permanent solution that can last for decades.

In order to use CIPP, your sewer pipes must be in good condition. First, your plumber will clean the pipes using hydro-jetting. This non-invasive, environmentally friendly cleaning solution will remove clogs and restore your pipes to their original diameter.

Next, your plumber will prepare the pipe for lining by scoring the surface with a saw or a blade. The scored area must be smooth and free of any cracks or breaks. A high-density polyethylene (HDPE) or fiberglass-reinforced pipe is usually used for lining, as these are long-lasting and resistant to corrosion.

Once the pipes are ready, your plumber will insert the lining material into the old pipe. A rubber bladder is inflated, and the epoxy coating on the inner surface of the liner cures to seal off any cracks or leaks. Once the pipe is fully lined, the contractor will remove the bladder, and you’ll have a brand-new pipe inside your old one!

Pipe bursting

A sewer pipe that bursts is a serious problem. The wastewater that you send down the drains is meant to travel through a series of pipes before reaching the treatment plant, so any problems with these pipes can cause significant damage to your home and even lead to dangerous health issues. The good news is that, thanks to advances in trenchless technology, you don’t need to dig up your floors or tear down walls to replace these pipes.

Instead, your plumber can use the trenchless method of pipe bursting to get you back on track quickly and effectively. This process involves digging two small holes on either end of the affected sewer line. From these points, a cable is run with a pneumatic jack on one end and a pipe bursting head attached to the other end. As the bursting head moves forward, it breaks up the old pipe and pulls in a new pipe at the same time, eliminating the need for excavation.

In addition to its speed, this method is ideal for homeowners who care about the appearance of their property. Traditional excavation methods can leave a mess and damage your landscaping or paved areas. By contrast, pipe bursting leaves no debris behind and can be completed in as little as a day.

This method of pipe replacement is also a great solution for anyone who wants to upsize their pipe size. Upgrading your pipes to a larger size can improve flow and water pressure, and this can help to prevent future blockages. It can also save you money on your utility bills in the long run.

This method of pipe repair is especially useful for older pipes that have corroded or collapsed. It is often used as a final solution for severely damaged sewer systems that can’t be repaired with other trenchless techniques. It can also be used to repair pipes that have been crushed by tree roots. While this technique is not available for every type of pipe, your licensed plumber will be able to help you determine whether or not it’s the best option for your situation.


If you’re dealing with a stubborn sewer line blockage that just won’t go away, it might be time to call in the big guns. Hydro jetting is a powerful, high-pressure water cleaning process that blasts clogs away and leaves your pipes looking like new. Here’s how it works:

First, your plumber will access your plumbing system through a cleanout, which is an opening in your sewer pipe designed for this purpose. Next, they’ll insert a nozzle attached to a hose that can handle the thousands of pounds of pressure that will be applied to it. The nozzle shoots water into the pipes at an angle, which both helps dislodge the clog and washes it away. Gravity takes over from there, pulling the loosened debris down into the cleanout.

Hydro jetting is a safe and effective method for cleaning your pipes because it uses nothing but highly pressurized water. This means it won’t cause any damage to your pipes, unlike chemical drain cleaners, which can eat through the walls of older pipes. It’s also more thorough than other methods, such as snaking, which can leave residues on the sides of your pipes.

The water pressure from the nozzle can break apart a wide range of materials that cause clogs, including hair, grease, minerals, food scraps, soap scum, and tree roots. It can even knock out intruding tree roots, which is important because these roots can damage your sewer pipes if they continue to grow inside them. The water pressure also washes away any dirt and debris that has accumulated inside the pipe, which can prevent clogs from forming in the future.

For these reasons, hydro jetting is often used to maintain residential and commercial sewer systems as well as municipal pipes. In fact, some property owners choose to have their sewer lines hydro jetted yearly or every other year. This prevents clogs from forming and reduces the risk of future problems, such as broken lines.

While a plumbing snake might be able to get rid of some clogs, it’s unlikely to work on hard-to-reach clogs. This is especially true for larger lines, such as those found in a home’s basement or at the end of the main sewer line outside their home. For these reasons, hydro jetting is usually the best solution for clearing tough clogs in commercial and municipal sewers.

Pipe replacement

If your sewer line is damaged beyond repair, you’ll need a professional to install a new one. The good news is that this can be done with relatively minimal disruption to your property.

The first step is to run a camera through the sewer lines to see what the problem is. This will show where the damage is located, and it’ll also help you decide whether a repair or replacement is best for your situation. The next step is to choose a contractor. Depending on the severity of the damage and where your sewer line is, you may need to replace an entire section of pipe.

A traditional sewer line replacement requires digging a trench throughout your yard to access the existing pipes. This can be very disruptive, especially if you have landscaping or a driveway near the line. You’ll need to dig up and replace these areas, and you’ll likely incur costs for repaving and restoring your landscaping.

Trenchless repair methods can be used to minimize the amount of damage caused during a sewer line replacement. For example, a technique called pipe relining can be used to repair minor cracks and leaks in a sewer line without replacing it entirely. During this process, a resin-coated liner is inserted into your old pipe. The liner adheres to the walls of your pipe, creating a strong seal against leaks and other damage.

Another option is to use a technique called pipe bursting. This involves installing a new sewer pipe without having to dig a trench. It works by feeding a cone-shaped head through the existing sewer pipe. This breaks the old pipe apart and draws in a new pipe, leaving behind a space that’s perfectly smooth and free from obstructions.

Harry Smith